DAM & POND SEALING
Bentonite quantity calculator
Enter the length and width of your treatment area, or the total area if you have already measured it, and choose an application rate.
Get an instant estimate in tonnes, bulk bags and product cost.
Compare all application rates
Quantities for 1,000 m². All bag counts are rounded up.
| Rate | Bentonite required | 1.2-tonne bags | Product cost (ex GST) |
|---|
A quantity estimate, not a sealing guarantee.
The calculation is length × width (or the total area you enter) = treatment area in m², then area × application rate in kg/m². Measurements in feet are converted to m² first. Product cost is the tonnes supplied in whole bags × $295 per tonne + GST ($354 + GST a bag), excluding delivery. Bag numbers show how many 1.2-tonne bulk bags you need. Lower rates are available for comparison, not as a recommendation to reduce treatment. Choose 35 or 40 kg/m² if you want to calculate a higher material allowance.
Soil conditions, the cause of leakage and installation affect the treatment required. Confirm your application rate and method before ordering. No allowance is added for losses or measurement uncertainty beyond the rate you select and whole-bag rounding.
Read the application guidanceHow much bentonite do I need to seal a dam?
Multiply the total surface area to be treated by Bentonite Pro’s recommended application rate of 30 kg/m², then divide the result by 1,200 kg and round up to whole bulk bags. Confirm soil suitability, the cause of leakage and the installation method before using that quantity to order material. See our application guidance for the rate and assessment requirements.
How do I measure the floor and sloping walls?
Use the surface that will receive treatment, including the floor and relevant sloping walls, rather than only the water surface or a rectangle drawn around the dam. These are the areas used in Bentonite Pro’s quantity calculation.
Work from a suitable survey or measurements that can be obtained safely. Do not enter deep water or work on unstable banks to obtain dimensions.
- Divide the treatment surface into manageable sections. Keep the floor and each sloping wall separate.
- Calculate a rectangular section as length × width. For a triangular section, use base × perpendicular height ÷ 2, with both measurements taken on that surface.
- Measure a wall along its sloping face, not just its horizontal width on a plan. Where the shape varies, break it into smaller sections rather than treating one width as exact.
- Add the section areas without overlap or omissions. The result is the total treatment area in square metres.
As an illustrative example, a 20 m × 10 m floor is 200 m². If separately measured wall sections total 300 m², the treatment area is 500 m², not 200 m².
The calculator does not model the dam’s slopes. If you already have a combined treatment area, such as 500 m², choose Total area and enter it directly.
What if the dam has an irregular shape?
A single average length and width is a preliminary estimate, not a survey of a curved or uneven surface. Use smaller measured sections where possible, and retain your area breakdown so the estimate can be checked before ordering.
If the floor is submerged or the wall shape is uncertain, arrange an assessment rather than treating a waterline measurement as the finished treatment area. NSW DPI’s Leaking farm dams guide also recommends checking the cause of water loss and soil suitability before selecting a repair.
How many bulk bags does that area require?
The examples below use 30 kg/m², 1,200 kg per bag and $295 + GST per tonne, with no allowance or freight added. They follow Bentonite Pro’s published quantity and whole-bag ordering method.
| Total treatment area | Bentonite required | Whole bags | Material in those bags | Product cost (ex GST) |
|---|---|---|---|---|
| 200 m² | 6,000 kg | 5 | 6,000 kg | $1,770 |
| 500 m² | 15,000 kg | 13 | 15,600 kg | $4,602 |
| 1,000 m² | 30,000 kg | 25 | 30,000 kg | $8,850 |
| 1,500 m² | 45,000 kg | 38 | 45,600 kg | $13,452 |
| 3,000 m² | 90,000 kg | 75 | 90,000 kg | $26,550 |
For the 500 m² example, 15,000 ÷ 1,200 = 12.5 bags. Rounding up gives 13 bags, with 600 kg above the calculated requirement.
For 1,500 m², 45,000 ÷ 1,200 = 37.5 bags. Rounding up gives 38 bags, or 45,600 kg, and 38 × 1.2 t × $295 = $13,452 + GST.
For 3,000 m², 90,000 ÷ 1,200 = 75 bags exactly, so no rounding is needed, and 75 × 1.2 t × $295 = $26,550 + GST.
One bag provides material for 40 m² at this rate before an allowance; this is calculated coverage, not a guarantee of sealing. The bulk-bag product page explains the pack size and coverage qualifications.
Is bag rounding the same as an allowance?
Rounding ensures the order contains at least the calculated mass, but it does not apply a chosen percentage allowance. For 500 m², the extra 600 kg from rounding is 4% of the 15,000 kg requirement.
If a site assessment supports a 5% allowance, the requirement becomes 15,750 kg; at 10%, it becomes 16,500 kg. Both require 14 whole bags, consistent with Bentonite Pro’s ordering examples.
The calculator does not add a separate percentage allowance automatically. Its higher-rate options change the selected kg/m², so do not treat them as a separate allowance control or add the same allowance twice; see the explanation already provided with the calculator.
What should I confirm before ordering?
Have the treatment area, soil assessment and proposed installation method checked together. A quantity calculation cannot establish that bentonite is the appropriate repair, and NSW DPI identifies several possible causes of leakage in its farm dam guidance.
For a delivered quote, provide your area breakdown, proposed bag quantity, delivery address and any agreed allowance. Confirm access, unloading and freight before committing to the order.
